当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM E32-1986(2006)e1 测定化学成分用铁合金及钢添加剂的取样
ASTM E32-1986(2006)e1 测定化学成分用铁合金及钢添加剂的取样
世界资料网 / 2019-12-14
【英文标准名称】: Standard Practices for Sampling Ferroalloys and Steel Additives for Determination of Chemical Composition
【原文标准名称】: 测定化学成分用铁合金及钢添加剂的取样
【标准号】: ASTM E32-1986(2006)e1
【标准状态】: 现行
【国别】:
【发布日期】: 1986
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: E01.01
【标准类型】: (Practice)
【标准水平】: ()
【中文主题词】: 抽样方法;铁合金;钢;工艺;金属;试样;添加剂;化学成分
【英文主题词】: chemical composition; ferroalloys; sampling; steel additives
【摘要】: These practices for the sampling of metals and alloys are primarily intended to test such materials for compliance with compositional specifications. It is assumed that all who use these methods will be trained samplers capable of performing common sampling procedures skillfully and safely.1.1 These practices include procedures for the sampling of the various ferroalloys and steel additives, either before or after shipment from the plants of the manufacturers. They are designed to give results representative of each lot that will be comparable with the manufacturer''s guaranteed analysis for the same lot. For check analysis, the purchaser may use any sampling procedure he desires, but the analytical results obtained on such samples shall not be a basis for complaint or rejection, unless the procedure followed is of an accuracy equivalent to that prescribed in these methods.1.2 In sampling ferroalloys and steel additives, serious errors often occur from contamination of the samples by iron from the sampling appliances. Therefore, special precautions should be observed to avoid this source of error. Metallic iron may be removed with a magnet from nonmagnetic alloys; its estimation in other alloys requires special analytical procedures (Note 0). To avoid this error, parts of crushers and pulverizing equipment contacting the samples shall be of steel or other material showing a high resistance to abrasion of the type involved. Note 0Metallic iron in ferrochromium and ferrosilicon may be determined as follows: Transfer 5 g of the sample of alloy to a 150-mL beaker, add 25 mL of HNO3 (1 + 3), cover, boil 5 min, filter into a 250-mL beaker, and wash with hot water. Add NH4OH in slight excess, heat to boiling, filter, and wash with hot water. Dissolve the precipitate on the paper with a minimum quantity of hot HCl (1 + 2), wash the filter with hot water, and titrate the iron by a standard procedure such as that described in Test Method E 354.1.3 The values stated in SI units are to be regarded as the standard. The inch-pound values in parenthesis are given for information only.This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中国标准分类号】: H11
【国际标准分类号】: 77_040_30 ; 77_100
【页数】: 5P.;A4
【正文语种】:

关键字: ASTM E32-

相关资料

ASTM E32-1986(2006)e1 测定化学成分用铁合金及钢添加剂的取样
ASTM E32-1986(2006)e1 测定化学成分用铁合金及钢添加剂的取样
ASTM B678-1986(2011) 金属涂覆产品的软钎焊性试验方法
ASTM D4581-1986(2005) 水体表面的形态学特性的测定
ASTM B555-1986(2007) 用点滴试验法测量电解沉积金属镀层厚度的标准指南
ASTM B699-1986(2008) 钢铁表面镉真空沉积镀层的标准规范
ASTM B766-1986(2008) 镉电沉积涂层的标准规范
ASTM C147-1986(2010) 玻璃容器的内压的标准试验方法
ASTM C149-1986(2010) 玻璃容器热冲击的标准试验方法
ASTM F992-1986(2006) 阀门铭牌标准规范
ASTM F993-1986(2006) 阀门锁紧装置标准规范
ASTM E1096-1986(2006) 实验室玻璃分液漏斗
ASTM F1027-1986(2007) 口腔颜面修补材料和器械同细胞组织和细胞相容性的评定
ASTM E1133-1986(2010) 美国政府征购的已包装的实验室设备的性能试验的标准实施规则
ASTM F1003-1986(1992) 摩托救生艇探照灯标准规范
ASTM F991-1986 泊船排水插塞及突台组件
ASTM F1020-1986(2006) 船用暗线阀
ASTM F1007-1986(2007) 套装滑动成型或船用管道膨胀节的标准规范
ASTM F994-1986(2006) 向船外排水船身渗透连接件的设计与安装
ASTM F986-1986(2008) 吸滤器外壳的标准规范
ASTM F1006-1986(2008) 船用管道装置用液滴分离器的标准规范
ASTM F1030-1986(2008) 门操作装置选择的标准作法
ASTM E1089-1986(2007) 均匀静气压差下平板太阳能收集器透水性的标准试验方法
ASTM E781-1986(2009) 暴露在有盖板的太阳能收集器中模拟滞流的条件下太阳能内存材料的吸收性评定的标准实施规范
ASTM E1084-1986(2009) 用阳光测试薄板材料的太阳能传递性(地面上)的标准试验方法
ASTM D116-1986(2006) 电气设备用上釉陶瓷材料的试验
ASTM F982-1986(2008) 静动脉连接用外科植入夹的特性表示的标准规范
ASTM F1026-1986(2008)e1 止血钳的一般工艺和性能测量的标准规范
ASTM F983-1986(2009) 整形植入件耐用标志的标准实施规程
ASTM D 4535-1985 用膨胀计测量岩石的热膨胀的试验方法
ASTM E 104-1985 用水溶液保持恒定相对湿度
ASTM D 4543-1985 岩石芯样制备及尺寸公差和形状公差测定的标准实施规程

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容: