当前位置: 首页 > 协会标准 > SAE 美国机动车工程师学会 > SAE AMS3004 Alcohol, Methyl (NONCURRENT Aug 2009)
SAE AMS3004 Alcohol, Methyl (NONCURRENT Aug 2009)
世界资料网 / 2019-11-19
Product Code:SAE AMS3004
Title:Alcohol, Methyl (NONCURRENT Aug 2009)
Issuing Committee:Ams B Finishes Processes And Fluids Committee
Scope:This specification has been declared “NONCURRENT” by the Aerospace Materials Division, SAE, as of August 2009. It is recommended, therefore, that this specification not be specified for new designs.“NONCURRENT” refers to those specifications which have previously been widely used and which may be required on some existing designs in the future. The Aerospace Materials Division, however, does not recommend these specifications for future use in new designs. “NONCURRENT” specifications are available from SAE upon request.
关键字: SAE AMS300

相关资料

SAE AMS3004 Alcohol, Methyl (NONCURRENT Aug 2009)
SAE AMS3004 Alcohol, Methyl (NONCURRENT Aug 2009)
SAE AMS4125 Aluminum Alloy Die Forgings, and Rolled or Forged Rings, 0.90Si - 0.62Mg - 0.25Cr, (6151-T6) Solution and Pr
SAE AMS5062 Steel, Low Carbon, Bars, Forgings, Tubing, Sheet, Strip, and Plate, 0.25 Carbon, Maximum (NONCURRENT Aug 200
SAE AMS7301 Steel, Highly-Stressed Springs, 0.95Cr - 0.20V (0.48 - 0.53C) (SAE 6150), Case Hardened (NONCURRENT Aug 2009
SAE AMSQQA591 Aluminum Alloy Die Castings (NONCURRENT Aug 2009)
SAE AMS4130 Aluminum Alloy Die Forgings, 4.4Cu - 0.85Si - 0.80Mn (2025-T6), Solution and Precipitation Heat Treated (NON
SAE AMS5042 Steel, Sheet and Strip, 0.15 Carbon, Maximum Forming Grade (NONCURRENT Aug 2009)
SAE AMS4140 Aluminum Alloy Die Forgings, 4.0Cu - 2.0Ni - 0.68Mg (2018-T61), Solution and Precipitation Heat Treated (NON
SAE AMS3002 Alcohol, Denatured Ethyl (NONCURRENT Aug 2009)
SAE ARP1322 Overpressurization Release Devices
SAE AS85720/1 Fittings, Tube, Fluid Systems, Separable, High Pressure, Dynamic Beam Seal, Design Standard for Male End
SAE AIR5651 History of Commercial Aircraft New Tire Qualification Testing
SAE AIR5493 Requirements for Development, Implementation and Control of Aerospace Auditor Training (Cancelled Jul 2009)
SAE AMS4117 Aluminum Alloy, Rolled or Cold Finished Bars, Rods, and Wire and Flash Welded Rings, 1.0Mg - 0.60Si - 0.28Cu
SAE ARP5862 Shipping Caps, Covers and Plugs
SAE AIR5715 Procedure for the Calculation of Aircraft Emissions
SAE AS39029/44 Contacts, Electrical Connector, Pin, Crimp Removable (For MIL-DTL-5015 Series MS3400 Connectors)
SAE AMS3101 Adhesion Promoter for Polysulfide Sealants, Non-crazing of Acrylic and Polycarbonate (NONCURRENT Jul 2009)
SAE AMS3202 Butadiene Acrylonitrile (NBR) Rubber, Dry Heat Resistant, 55 - 65
SAE AMS3625 Elastomeric Tubing, Electrical Insulation, Crosslinked Silicone, Pigmented, Flexible, Heat-Shrinkable, 1.750
SAE AMS3755 Powder, Fumed Silicon Dioxide
SAE AS7458 Studs, Steel, Low Alloy, Heat Resistant, Normalized and Tempered, Roll Threaded, 135 000 psi Tensile Strength
SAE AMS3690 Adhesive Compound, Epoxy, Room Temperature Curing
SAE ARP1313 Determination of Trace Elements in High Temperature Alloys
SAE AMS2759/2 Heat Treatment of Low-Alloy Steel Parts, Minimum Tensile Strength 220 ksi (1517 MPa) and Higher
SAE AS7456 Studs, Steel, Low Alloy Heat Treated, Roll Threaded
SAE AMS2355 Quality Assurance, Sampling and Testing, Aluminum Alloys and Magnesium Alloy, Wrought Products (Except Forgi
SAE AMS2249 Chemical Check Analysis Limits, Titanium and Titanium Alloys
SAE AMS3412 Flux, Aluminum Brazing for Torch or Furnance Brazing
SAE AMS4855 Leaded Red Brass, Sand and Centrifugal Castings, 85Cu - 5.0Sn - 5.0Pb - 5.0Zn, As Cast
SAE AMS4785 Gold-Palladium-Nickel Alloy, Brazing Filler Metal, High Temperature, 30Au - 34Pd - 36Ni, 2075 to 2130 °F (11

用户评论(共0条评论)

  • 暂时还没有任何用户评论
总计 0 个记录,共 1 页。 第一页 上一页 下一页 最末页
用户名: 匿名用户
E-mail:
评价等级:
评论内容: