当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM D2837-2008 获得热塑性管道材料静水压设计基数或热塑性管道制品用压力设计基数的试验方法
ASTM D2837-2008 获得热塑性管道材料静水压设计基数或热塑性管道制品用压力设计基数的试验方法

ASTM D2837-2008 获得热塑性管道材料静水压设计基数或热塑性管道制品用压力设计基数的试验方法

prev next

  • 商品货号:INFOEACH_80981
  • 商品品牌:美国材料与试验协会 ASTM
    商品重量:0克
  • 上架时间:2021-03-02
    商品点击数:5000
  • 用户评价: comment rank 5
  • 本店售价:请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products
【原文标准名称】: 获得热塑性管道材料静水压设计基数或热塑性管道制品用压力设计基数的试验方法
【标准号】: ASTM D2837-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: F17.40
【标准类型】: (Test Method)
【标准水平】: ()
【中文主题词】:
【英文主题词】: Circumferential expansion; Design--piping systems; Hydrostatic design basis (HDB); Polyethylene (PE) pipe; Stress--plastics; Thermoplastic pipe/tube/fittings; Validation
【摘要】: The procedure for estimating long-term hydrostatic strength or pressure-strength is essentially an extrapolation with respect to time of a stress-time or pressure-time regression line based on data obtained in accordance with Test Method D 1598. Stress or pressure-failure time plots are obtained for the selected temperature and environment: the extrapolation is made in such a manner that the long-term hydrostatic strength or pressure strengthis estimated for these conditions. Note 38212;Test temperatures should preferably be selected from the following: 40x00B0;C; 50x00B0;C; 60x00B0;C; 80x00B0;C; 100x00B0;C. It is strongly recommended that data also be generated at 23x00B0;C for comparative purposes. The hydrostatic or pressure design basis is determined by considering the following items and evaluating them in accordance with 5.4. Long-term hydrostatic strength or hydrostatic pressure-strength at 100 000 h, Long-term hydrostatic strength or hydrostatic pressure-strength at 50 years, and Stress that will give 5 % expansion at 100 000 h. The intent is to make allowance for the basic stress-strain characteristics of the material, as they relate to time. Results obtained at one temperature cannot, with any certainty, be used to estimate values for other temperatures. Therefore, it is essential that hydrostatic or pressure design bases be determined for each specific kind and type of plastic compound and each temperature. Estimates of long-term strengths of materials can be made for a specific temperature provided that calculated values, based on experimental data, are available for temperatures both above and below the temperature of interest. Hydrostatic design stresses are obtained by multiplying the hydrostatic design basis values by a service (design) factor. Pressure ratings for pipe may be calculated from the hydrostatic design stress (HDS) value for the specific material used to make the pipe, and its dimensions using the equations in 3.1.11. 4.5.1 Pressure ratings for multilayer pipe may be calculated by multiplying the pressure design basis (PDB) by the appropriate design factor (DF).1.1 This test method describes two essentially equivalent procedures: one for obtaining a long-term hydrostatic strength category based on stress, referred to herein as the hydrostatic design basis (HDB); and the other for obtaining a long-term hydrostatic strength category based on pressure, referred to herein as the pressure design basis (PDB). The HDB is based on the material''s long-term hydrostatic strength (LTHS),and the PDB is based on the product''s long-term hydrostatic pressure-strength (LTHSP). The HDB is a material property and is obtained by evaluating stress rupture data derived from testing pipe made from the subject material. The PDB is a product specific property that reflects not only the properties of the material(s) from which the product is made, but also the influence on product strength by product design, geometry, and dimensions and by the specific method of manufacture. The PDB is obtained by evaluating pressure rupture data. The LTHS is determined by analyzing stress versus time-to-rupture (that is, stress-rupture) test data that cover a testing period of not less than 10 000 h and that are derived from sustained pressure testing of pipe made from the subject material. The data are analyzed by linear regression to yield a best-fit log-stress versus log time-to-fail straight-line equation. Using this equation, the material''s mean strength at the 100 000-h intercept (LTHS) is determined by extrapolation. The resultant ......
【中国标准分类号】: P94
【国际标准分类号】: 83_140_30
【页数】: 16P.;A4
【正文语种】: 英语

相关资料