当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM C390-2008e1 批量预制的隔热材料的抽样和验收的标准实施规程
ASTM C390-2008e1 批量预制的隔热材料的抽样和验收的标准实施规程

ASTM C390-2008e1 批量预制的隔热材料的抽样和验收的标准实施规程

prev next

  • 商品货号:INFOEACH_80967
  • 商品品牌:美国材料与试验协会 ASTM
    商品重量:0克
  • 上架时间:2021-03-06
    商品点击数:5950
  • 用户评价: comment rank 5
  • 本店售价:请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Practice for Sampling and Acceptance of Thermal Insulation Lots
【原文标准名称】: 批量预制的隔热材料的抽样和验收的标准实施规程
【标准号】: ASTM C390-2008e1
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: C16.31
【标准类型】: (Practice)
【标准水平】: ()
【中文主题词】:
【英文主题词】: batts; blanket; block; board; pipe; preformed; sampling and acceptance; thermal insulation; Acceptance criteria/testing; Preformed thermal insulation; Sampling thermal insulating materials; Thermal insulating materials
【摘要】: The sampling and inspection prescribed in this standard afford the purchaser a practical level of quality assurance on incoming material. They are based on cost/risk relationships considered typical for preformed thermal insulations offered for general use. In all cases, the purchaser should review this standard and determine its suitability in terms of his specific needs. This procedure is intended primarily for the inspection of a continuing stream of lots, and there is not a high probability of rejecting occasional off lots. Consumer protection is based on economic pressure on the producer, through greater risk of lot rejection, to maintain the process average at 90 % conformance or better. Operating characteristic curves for the sampling plans employed can be found in Practice E 2234, Table X-C through Table X-F. It is not the intent of this procedure to estimate lot quality, control the quality of production, relieve the supplier of responsibility for the quality of material offered, or determine the disposition of material found to be defective after receipt by the purchaser.1.1 This standard provides criteria for establishing the acceptability of lots of shipments of preformed board, preformed block and pipe, and batts and blanket thermal insulation based on sampling and inspection. 1.2 This standard is intended for use in conjunction with appropriate ASTM material specifications that classify and describe the specific physical requirements for the product in terms of qualification requirements and inspection requirements. Determination of nonconformity shall be based on the tolerances for individual sample test values prescribed in the material specification. 1.3 This standard may require inspection substantially different from that performed in the normal course of production. If the purchaser requires sampling and acceptance inspection in accordance with this practice, he shall so specify in the order or contract. 1.4 The vales stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中国标准分类号】: Q25
【国际标准分类号】: 91_100_60
【页数】: 4P.;A4
【正文语种】: 英语

相关资料