当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM D4729-2008 使用扁千斤顶法现场测定变形的应力和模数的标准试验方法

资料类别

相关资料

ASTM D4729-2008 使用扁千斤顶法现场测定变形的应力和模数的标准试验方法

ASTM D4729-2008 使用扁千斤顶法现场测定变形的应力和模数的标准试验方法

prev next

  • 商品货号：INFOEACH_80883
  • 商品品牌：美国材料与试验协会 ASTM
    商品重量：0克
  • 上架时间：2021-02-27
    商品点击数：5623
  • 用户评价： comment rank 5
  • 本店售价：请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Test Method for In Situ Stress and Modulus of Deformation Using Flatjack Method
【原文标准名称】: 使用扁千斤顶法现场测定变形的应力和模数的标准试验方法
【标准号】: ASTM D4729-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: D18.12
【标准类型】: (Test Method)
【标准水平】: ()
【中文主题词】:
【英文主题词】: creep; flatjack hydraulic pressure; in situ stress; modulus of deformation; Deformation--rock; Drilling (in soil/rock); Field testing--rock; Flatjack method; Gages; Isotropic rock specimens; Modulus--soil/rock applications; Rock materials/properties/analy
【摘要】: Tests in Orthogonal Directions8212;The flatjack most accurately determines the stress parallel to the long axis of the adit, because this stress is the least affected by the presence of the opening. (The other tangential stress is highly concentrated.) In addition, if the adit is in a stress field where one of the stresses is significantly larger than the others (3 or 4 times), certain locations in the adit may be in very low compressive or even tensile stress. Flatjack tests in these locations can give anomalous and misleading results. Because of these factors, the test adit should have at least two, and preferably three, long (at least 4 to 5 times the diameter), straight sections at about 90x00B0; to each other. Testing should be distributed evenly in all three sections to provide redundant data and, if results in one section are anomalous, to allow the program to produce sufficient usable data. Note 18212;Not withstanding the statements on precision and bias contained in this test method; the precision of this test method is dependent on the competence of the personnel performing it, and the suitability of the equipment and facilities used. Agencies that meet the criteria of Practice D 3740 are generally considered capable of competent and objective testing. Users of this test method are cautioned that compliance with Practice D 3740 does not in itself assure reliable testing. Reliable testing depends on many factors; Practice D 3740 provides a means of evaluating some of those factors.1.1 The flatjack test measures stress at a rock surface. The modulus of deformation and the long-term deformational properties (creep) may also be evaluated. 1.2 All observed and calculated values shall conform to the guidelines for significant digits and rounding established in Practice D 6026. 1.2.1 The method used to specifiy how data are collected, calculated, or recorded in this standard is not directly related to the accuracy to which the data can be applied in design or other uses, or both. How one applies the results obtained using this standard is beyond its scope. 1.3 Limitation8212;The flatjack test measures the average stress normal to the surface of the test chamber. Undisturbed stress levels must be determined by theoretical interpretations of these data. 1.4 Assumptions and Factors Influencing the Data: 1.4.1 The stress relief is assumed to be an elastic, reversible process. In nonhomogeneous or highly fractured materials, this may not be completely true. 1.4.2 The equations assume that the rock mass is isotropic and homogeneous. Anisotropic effects may be estimated by testing in different orientations. 1.4.3 The flatjack is assumed to be 100 % efficient. The design and size requirements of 7.1 were determined to satisfy this requirement to within a few percent. 1.4.4 The jack is assumed to be aligned with the principal stresses on the surface of the opening. Shear stresses are not canceled by jack pressure. Orientating the tests in three directions in each plane tested prevents the misalignment from being excessive for at least one of the tests. 1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated wit......
【中国标准分类号】: P21
【国际标准分类号】: 93_020
【页数】: 6P.;A4
【正文语种】: 英语

标签

ASTM[1] D4729-[1]

相关资料

免责条款 - 隐私保护 - 联系我们 - 公司简介 - 批发方案 - 配送方式 - 支付方式 - 法律顾问：北京贾忠强律师