资料描述
【英文标准名称】: Standard Specification for Stainless Steel Socket Head Cap Screws
【原文标准名称】: 不锈钢内六角头有头螺钉标准规范
【标准号】: ASTM F837-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: F16.04
【标准类型】: (Specification)
【标准水平】: ()
【中文主题词】:
【英文主题词】: corrosion resistant; stainless steel; socket head cap screws; Head cap screws; Screws--specifications; Stainless steel screws--specifications; Steel screws--specifications
【摘要】: 1.1 This specification covers the chemical and mechanical requirements for stainless steel inch socket head cap screw (SHCS) with nominal thread 0.060 through 1.500 in. and intended for use in applications requiring general corrosion resistance. 1.2 Three groups of stainless steel alloys are covered, austenitic Group 1 and 2 and martensitic Group 5. 1.3 Four property conditions are covered: austenitic Alloy Groups 1 and 2 in an annealed condition (AF) at 85 ksi maximum, in two cold worked conditions (CW) at 80 ksi minimum, (CW1) at 102 ksi minimum, and martensitic Alloy Group 5 in a heat treated condition (HT) at 160 ksi minimum. 1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. 1.5 The following precautionary caveat pertains only to the test method portion, Section 13, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中国标准分类号】: J13
【国际标准分类号】: 21_060_10
【页数】: 8P.;A4
【正文语种】: 英语
ASTM F2482-2008 负荷指示外螺纹紧固件用标准规范
【英文标准名称】: Standard Specification for Load-Indicating Externally Threaded Fasteners
【原文标准名称】: 负荷指示外螺纹紧固件用标准规范
【标准号】: ASTM F2482-2008
【标准状态】: 现行
【国别】: 美国
ASTM F2649-2008a 波纹状高密度聚乙烯(HDPE)油脂拦截槽用规范
【英文标准名称】: Standard Specification for Corrugated High Density Polyethylene (HDPE) Grease Interceptor Tanks
【原文标准名称】: 波纹状高密度聚乙烯(HDPE)油脂拦截槽用规范
【标准号】: ASTM F2649-2008a
【标准状态】: 现行
ASTM C1460-2008 地上用不同DWV管和配件用屏蔽转换联结器的标准规范
【英文标准名称】: Standard Specification for Shielded Transition Couplings for Use With Dissimilar DWV Pipe and Fittings Above Ground
【原文标准名称】: 地上用不同DWV管和配件用屏蔽转换联结器的标准规范
【标准号】: ASTM C1460-2008
【标准状态】:
ASTM E1402-2008e1 取样的相关标准术语
【英文标准名称】: Standard Terminology Relating to Sampling
【原文标准名称】: 取样的相关标准术语
【标准号】: ASTM E1402-2008e1
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日
ASTM D1535-2008e1 用孟塞尔色系规定颜色的标准实施规程
【英文标准名称】: Standard Practice for Specifying Color by the Munsell System
【原文标准名称】: 用孟塞尔色系规定颜色的标准实施规程
【标准号】: ASTM D1535-2008e1
【标准状态】: 现行
【国别】:
【发布日期】:
ASTM E2630-2008e1 使用窄带源测定荧光标本的亮度比的标准试验方法
【英文标准名称】: Standard Test Method for Luminance Ratio of a Fluorescent Specimen using a Narrow Band Source
【原文标准名称】: 使用窄带源测定荧光标本的亮度比的标准试验方法
【标准号】: ASTM E2630-2008e1
【标准状态】: 现行
ASTM A754/A754M-2008 X射线荧光涂层厚度的标准试验方法
【英文标准名称】: Standard Test Method for Coating Weight (Mass) of Metallic Coatings on Steel by X-Ray Fluorescence
【原文标准名称】: X射线荧光涂层厚度的标准试验方法
【标准号】: ASTM A754/A754M-2008
【标准状态】: 现行
ASTM D1654-2008 腐蚀环境中涂漆或覆层试样评估的标准试验方法
【英文标准名称】: Standard Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments
【原文标准名称】: 腐蚀环境中涂漆或覆层试样评估的标准试验方法
【标准号】: ASTM D1654-2008
【标准状态】: 现行
ASTM A1059/A1059M-2008 用于钢紧固件、五金制品及其他产品的具有热扩散涂层(TDC)锌合金的标准规范
【英文标准名称】: Standard Specification for Zinc Alloy Thermo-Diffusion Coatings (TDC) on Steel Fasteners, Hardware, and Other Products
【原文标准名称】: 用于钢紧固件、五金制品及其他产品的具有热扩散涂层(TDC)锌合金的标准规范
【标准号】: ASTM A1059/A1059M-2008
ASTM D7449/D7449M-2008 使用同轴空气电缆测量微波频率下固体材料相对复合电容率和相对磁导率的标准试验方法
【英文标准名称】: Standard Test Method for Measuring Relative Complex Permittivity and Relative Magnetic Permeability of Solid Materials at Microwave Frequencies Using Coaxial Air Line
【原文标准名称】: 使用同轴空气电缆测量微波频率下固体材料相对复合电容率和相对磁导率的标准试验方法
ASTM D6617-2008 用标准物质的单项试验结果检测实验室偏差的标准实施规程
【英文标准名称】: Standard Practice for Laboratory Bias Detection Using Single Test Result from Standard Material
【原文标准名称】: 用标准物质的单项试验结果检测实验室偏差的标准实施规程
【标准号】: ASTM D6617-2008
【标准状态】: 现行
ASTM D4635-2008a 通用和包装用低密度聚乙烯薄膜标准规范
【英文标准名称】: Standard Specification for Polyethylene Films Made from Low-Density Polyethylene for General Use and Packaging Applications
【原文标准名称】: 通用和包装用低密度聚乙烯薄膜标准规范
【标准号】: ASTM D4635-2008a
【标准状
ASTM E2655-2008 ASTM试验方法中术语测量不确定性的使用和试验结果不确定性的报告用标准指南
【英文标准名称】: Standard Guide for Reporting Uncertainty of Test Results and Use of the Term Measurement Uncertainty in ASTM Test Methods
【原文标准名称】: ASTM试验方法中术语测量不确定性的使用和试验结果不确定性的报告用标准指南
【标准号】: ASTM E2655-2008
ASTM D5367-2008 用水或水/磨料喷洗时为防止钢生薄锈用抑制剂处理的表面镀层的评估用标准实施规程
【英文标准名称】: Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
【原文标准名称】: 用水或水/磨料喷洗时为防止钢生薄锈用抑制剂处理的表面镀层的评估用标准实施规程
ASTM E308-2008 用CIE体系估计物体颜色的标准实施规程
【英文标准名称】: Standard Practice for Computing the Colors of Objects by Using the CIE System
【原文标准名称】: 用CIE体系估计物体颜色的标准实施规程
【标准号】: ASTM E308-2008
【标准状态】: 现行
【国别】: 美国
ASTM E598-2008 用瞬变零点量热器测量高能环境的超级传热速率的标准试验方法
【英文标准名称】: Standard Test Method for Measuring Extreme Heat-Transfer Rates from High-Energy Environments Using a Transient, Null-Point Calorimeter
【原文标准名称】: 用瞬变零点量热器测量高能环境的超级传热速率的标准试验方法
【标准号】: ASTM E598-2008
ASTM F2717-2008 发展第三方独立认证的标准指南
【英文标准名称】: Standard Guide for Development of an Independent Third-Party Verification
【原文标准名称】: 发展第三方独立认证的标准指南
【标准号】: ASTM F2717-2008
【标准状态】: 现行
【国别】: 美国
ASTM E2609-2008 刚性聚合物包装中气味或味道渗出或两者同时进行的标准试验方法
【英文标准名称】: Standard Test Method for Odor or Flavor Transfer or Both from Rigid Polymeric Packaging
【原文标准名称】: 刚性聚合物包装中气味或味道渗出或两者同时进行的标准试验方法
【标准号】: ASTM E2609-2008
【标准状态】: 现行
ASTM E2164-2008 定向差测试的标准试验方法
【英文标准名称】: Standard Test Method for Directional Difference Test
【原文标准名称】: 定向差测试的标准试验方法
【标准号】: ASTM E2164-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
ASTM F519-2008 电镀/涂层处理和设备环境的机械氢脆化评价的标准试验方法
【英文标准名称】: Standard Test Method for Mechanical Hydrogen Embrittlement Evaluation of Plating/Coating Processes and Service Environments
【原文标准名称】: 电镀/涂层处理和设备环境的机械氢脆化评价的标准试验方法
【标准号】: ASTM F519-2008