当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM D5162-2008 金属衬底上非传导保护涂料的间断性(假期)检验标准实施规程

资料类别

相关资料

ASTM D5162-2008 金属衬底上非传导保护涂料的间断性(假期)检验标准实施规程

ASTM D5162-2008 金属衬底上非传导保护涂料的间断性(假期)检验标准实施规程

prev next

  • 商品货号：INFOEACH_80806
  • 商品品牌：美国材料与试验协会 ASTM
    商品重量：0克
  • 上架时间：2021-03-04
    商品点击数：5397
  • 用户评价： comment rank 5
  • 本店售价：请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Practice for Discontinuity (Holiday) Testing of Nonconductive Protective Coating on Metallic Substrates
【原文标准名称】: 金属衬底上非传导保护涂料的间断性(假期)检验标准实施规程
【标准号】: ASTM D5162-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: D01.46
【标准类型】: (Practice)
【标准水平】: ()
【中文主题词】:
【英文主题词】: discontinuity; high voltage; holiday; holiday detectors; low voltage; new linings; spark testers ; wet sponge type instruments; Discontinuities--coatings; Electrical measurements--coating applications; Substrates--coating applications; Substrates--metalli
【摘要】: A coating is applied to a metallic substrate to prevent corrosion, reduce abrasion or reduce product contamination, or all three. The degree of coating continuity required is dictated by service conditions. Discontinuities in a coating are frequently very minute and not readily visible. This practice provides a procedure for electrical detection of minute discontinuities in nonconductive coating systems. Electrical testing to determine the presence and number of discontinuities in a coating film is performed on a nonconductive coating applied to an electrically conductive surface. The allowable number of discontinuities should be determined prior to conducting this test since the acceptable quantity of discontinuities will vary depending on coating film thickness, design, and service conditions. The low voltage wet sponge test equipment is generally used for determining the existence of discontinuities in coating films having a total thickness of 0.5 mm (20 mil) or less. High voltage spark test equipment is generally used for determining the existences of discontinuities in coating films having a total thickness of greater than 0.5 mm (20 mil). Coatings that are applied at a thickness of less than 0.5 mm (20 mil) may be susceptible to damage if tested with high voltage spark testing equipment. Consult the coating manufacturer for proper test equipment and inspection voltages. To prevent damage to a coating film when using high voltage test instrumentation, total film thickness and dielectric strength in a coating system shall be considered in selecting the appropriate voltage for detection of discontinuities. Atmospheric conditions shall also be considered since the voltage required for the spark to gap a given distance in air varies with the conductivity of the air at the time the test is conducted. Suggested starting voltages are provided in Table 1. The coating manufacturer shall be consulted to obtain the following information, which would affect the accuracy of this test to determine discontinuities: Establish the length of time required to adequately dry or cure the applied coating film prior to testing. Solvents retained in an uncured coating film may form an electrically conductive path through the film to the substrate. Determine whether the coating contains electrically conductive fillers or pigments that may affect the normal dielectric properties. This practice is intended for use with new linings applied to metal substrates. Its use on a coating previously exposed to an immersion condition has often resulted in damage to the coating and has produced erroneous detection of discontinuities due to permeation or moisture absorption of the coating. Deposits may also be present on the surface causing telegraphing (current traveling through a moisture path to a discontinuity, giving an erroneous indication) or current leakage across the surface of the coating due to contamination. The use of a high voltage tester on previously exposed coatings has to be carefully considered because of possible spark-through, which will damage an otherwise sound coating. Although a low voltage tester can be used without damaging the coating, it may also produce erroneous results.1.1 This practice covers procedures for determining discontinuities using two types of test equipment: 1.1.1 Test Method A8212;Low Voltage Wet Sponge, and 1.1.2 Test Method B8212;High Voltage Spark Testers. 1.2 This practice addresses metallic substrates. For concrete surfaces, refer to Practice D 4787. 1.3 The values stated in SI units are to re regarded as the standard. The values given in parentheses ......
【中国标准分类号】: A29
【国际标准分类号】: 25_220_20
【页数】: 5P.;A4
【正文语种】: 英语

标签

ASTM[1] D5162-[1]

相关资料

免责条款 - 隐私保护 - 联系我们 - 公司简介 - 批发方案 - 配送方式 - 支付方式 - 法律顾问：北京贾忠强律师