当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM F1084-2008 漏油回收设备用油水混合物样品的采集的标准指南

资料类别

相关资料

ASTM F1084-2008 漏油回收设备用油水混合物样品的采集的标准指南

ASTM F1084-2008 漏油回收设备用油水混合物样品的采集的标准指南

prev next

  • 商品货号：INFOEACH_80739
  • 商品品牌：美国材料与试验协会 ASTM
    商品重量：0克
  • 上架时间：2021-02-26
    商品点击数：5098
  • 用户评价： comment rank 5
  • 本店售价：请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Guide for Sampling Oil/Water Mixtures for Oil Spill Recovery Equipment
【原文标准名称】: 漏油回收设备用油水混合物样品的采集的标准指南
【标准号】: ASTM F1084-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: F20.12
【标准类型】: (Guide)
【标准水平】: ()
【中文主题词】:
【英文主题词】: oil spill; oil spill recovery; oil/water mixtures; Contamination--environmental; Mixtures (oil/water); Oil spill control systems; Oil-water mixtures; Sampling oils; Sampling water analysis applications
【摘要】: This guide provides techniques for obtaining representative samples of oil and water mixtures. This information is necessary in the calculation of oil recovery efficiency and oil recovery rates for oil collection devices. Sampling Stationary Mixtures8212;When recovered oil/water mixtures are contained within a holding tank and the relative oil content of the recovered fluid is needed, the sampling technique is somewhat dependent on the container. Two techniques are outlined in this guide. If the container has a flat bottom with straight sides perpendicular to the base (or nearly so), either stationary technique can be implemented, with the stratified sampling method preferred. If the container is irregular in either the horizontal or vertical cross section, the mixing method is preferred. Sampling Flowing Mixtures8212;To sample flowing mixtures containing both oil and water, turbulence is induced, to create a homogenous mixture while sampling. The oil content in the sample taken from the flowing stream can then be used to quantify the performance-rating criterion (see Procedure Section of Test Method D 1796).1.1 This guide is intended for sampling flowing or stationary oil/water mixtures. It is intended for use with oil spill recovery devices either in testing or in documentation of field performance. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中国标准分类号】: J88
【国际标准分类号】: 13_060_10
【页数】: 3P.;A4
【正文语种】: 英语

标签

ASTM[1] F1084-[1]

相关资料

免责条款 - 隐私保护 - 联系我们 - 公司简介 - 批发方案 - 配送方式 - 支付方式 - 法律顾问：北京贾忠强律师