当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM A694/A694M-2008 高压部件传输用管法兰,配件,阀门及零件用碳素钢及合金钢锻件的标准规范

资料类别

相关资料

ASTM A694/A694M-2008 高压部件传输用管法兰,配件,阀门及零件用碳素钢及合金钢锻件的标准规范

ASTM A694/A694M-2008 高压部件传输用管法兰,配件,阀门及零件用碳素钢及合金钢锻件的标准规范

prev next

  • 商品货号：INFOEACH_80610
  • 商品品牌：美国材料与试验协会 ASTM
    商品重量：0克
  • 上架时间：2021-03-08
    商品点击数：5664
  • 用户评价： comment rank 5
  • 本店售价：请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Specification for Carbon and Alloy Steel Forgings for Pipe Flanges, Fittings, Valves, and Parts for High-Pressure Transmission Service
【原文标准名称】: 高压部件传输用管法兰,配件,阀门及零件用碳素钢及合金钢锻件的标准规范
【标准号】: ASTM A694/A694M-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: A01.22
【标准类型】: (Specification)
【标准水平】: ()
【中文主题词】:
【英文主题词】: high strength low alloy steel; pipe fittings, steel; piping applications; pressure containing parts; steel flanges; steel forgings, alloy; steel forgings, carbon; steel valves; Alloy steel forgings--specifications; Carbon steel forgings--specifications; H
【摘要】: 1.1 This specification covers forged or rolled steel pipe flanges, forged fittings, valves, and parts suitable for use with high-strength transmission-service pipe. Included are flanges, fittings, and similar parts ordered either to dimensions specified by the purchaser or to ASME or MSS dimensional standards referenced in Section 2. 1.2 Several grades of material, based on minimum yield strength requirements, are covered, as indicated in Table 1. 1.3 Supplementary Requirements are provided. Supplementary Requirement S 1 is provided for use when purchaser approval is required for repair welding. 1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation (SI units), the material shall be furnished to inch-pound units. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the standard. TABLE 1 Tensile Requirements Grade Yield Strength (0.2 % Offset), min, ksi [MPa] Tensile Strength, min, ksi [MPa]Elongation in 2 in. or 50 mm, min % F42
42 [290]
60 [415]
20
F46
46 [315]
60 [415]
20
F48
48 [330]
62 [425]
20
F50
50 [345]
64 [440]
20
F52
52 [360]
66 [455]
20
F56
56 [385]
68 [470]
20
F60
60 [415]
75 [515]
20
F65
65 [450]
77 [530]
20
F70
70 [485]
82 [565]
18

标签

ASTM[1] A694A6[1]

相关资料

免责条款 - 隐私保护 - 联系我们 - 公司简介 - 批发方案 - 配送方式 - 支付方式 - 法律顾问：北京贾忠强律师