当前位置: 首页 > 协会标准 > ASTM 美国材料与试验协会 > ASTM A275/A275M-2008 钢锻件磁粉检查的标准实施规程

资料类别

相关资料

ASTM A275/A275M-2008 钢锻件磁粉检查的标准实施规程

ASTM A275/A275M-2008 钢锻件磁粉检查的标准实施规程

prev next

  • 商品货号：INFOEACH_80598
  • 商品品牌：美国材料与试验协会 ASTM
    商品重量：0克
  • 上架时间：2021-03-03
    商品点击数：5271
  • 用户评价： comment rank 5
  • 本店售价：请咨询客服
  • 点击此处进入论坛自助下载

资料描述

【英文标准名称】: Standard Practice for Magnetic Particle Examination of Steel Forgings
【原文标准名称】: 钢锻件磁粉检查的标准实施规程
【标准号】: ASTM A275/A275M-2008
【标准状态】: 现行
【国别】: 美国
【发布日期】: 2008
【实施或试行日期】:
【发布单位】: 美国材料与试验协会(US-ASTM)
【起草单位】: A01.06
【标准类型】: (Test Method)
【标准水平】: ()
【中文主题词】:
【英文主题词】: circular magnetization; d c magnetization; dry method; fluorescent method; longitudinal magnetization; steel forgings; surface flaw detection; wet method; Defects; Forgings; Magnetic particle inspection; Steel forgings; Surface analysis--metals/alloys; Vi
【摘要】: For ferromagnetic materials, magnetic particle examination is widely specified for the detection of surface and near surface discontinuities such as cracks, laps, seams, and linearly oriented nonmetallic inclusions. Such examinations are included as mandatory requirements in some forging standards such as Specification A 508/A 508M. Use of direct current or rectified alternating (full or half wave) current as the power source for magnetic particle examination allows detection of subsurface discontinuities.1.1 This practice covers a procedure for magnetic particle examination of steel forgings. The procedure will produce consistent results upon which acceptance standards can be based. This standard does not contain acceptance standards or recommended quality levels. 1.2 Only direct current or rectified alternating (full or half wave) current shall be used as the electric power source for any of the magnetizing methods. Alternating current is not permitted because its capability to detect subsurface discontinuities is very limited and therefore unsuitable. 1.2.1 Portable battery powered electromagnetic yokes are outside the scope of this practice. Note 18212;Guide E 709 may be utilized for magnetic particle examination in the field for machinery components originally manufactured from steel forgings. 1.3 The minimum requirements for magnetic particle examination shall conform to practice standards of Practice E 1444. If the requirements of this practice are in conflict with the requirements of Practice E 1444, the requirements of this practice shall prevail. 1.4 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable x201C;Mx201D; specification designation [SI units], the material shall be furnished to inch-pound units. 1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. 1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
【中国标准分类号】: H26
【国际标准分类号】: 77_140_85
【页数】: 7P.;A4
【正文语种】: 英语

标签

ASTM[1] A275A2[1]

相关资料

免责条款 - 隐私保护 - 联系我们 - 公司简介 - 批发方案 - 配送方式 - 支付方式 - 法律顾问：北京贾忠强律师