资料描述
【英文标准名称】: Test Method for Determination of Isothermal Secant and Tangent Bulk Modulus
【原文标准名称】: 等温正割和正切体积弹性模量测定方法
【标准号】: ANSI/ASTM D6793-2002
【标准状态】: 作废
【国别】: 美国
【发布日期】: 2002
【实施或试行日期】:
【发布单位】: 美国国家标准学会(US-ANSI)
【起草单位】: ANSI
【标准类型】: ()
【标准水平】: ()
【中文主题词】:
【英文主题词】: Bulk modulus;Determination;Isothermal;Test method
【摘要】: This test method covers the determination of isothermal secant and tangent bulk modulus of liquids which are stable and compatible with stainless steel under the conditions of test. This test method is designed to be used over the temperature range from -40 to 200?C and from ambient to 68.95 Mpa (10 000 psig). Note 1Because of the design of the test apparatus, the upper limit of pressure which can be attained is limited by the bulk modulus of the test fluid. Pressures as high as 68.95 Mpa will not be attained for fluids of relatively low bulk modulus at the test temperature. This test method assumes that the user is proficient in the assembly and use of medium pressure (m/p) threaded and coned fittings which are intended for use at pressures up to 137.9 Mpa (20 000 psig). This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Note 2Because hydraulic pressure in the test system is produced by purely mechanical means, the test method is not subject to the hazards associated with systems which are pressurized pneumatically. Even small leaks will result in immediate drop in pressure to ambient without production of a high pressure liquid stream or mist.
【中国标准分类号】: J04
【国际标准分类号】: 75_160_20
【页数】:
【正文语种】: 英语
ANSI/ASTM D1748-2002 在湿度室里测定金属防腐剂的防锈性能的试验方法
【英文标准名称】: Test Method for Rust Protection by Metal Preservatives in the Humidity Cabinet
【原文标准名称】: 在湿度室里测定金属防腐剂的防锈性能的试验方法
【标准号】: ANSI/ASTM D1748-2002
【标准状态】: 作废
【国别】:
ANSI/AWS D8.9-2002 汽车薄型钢材的耐点焊特性试验方法的推荐性惯例
【英文标准名称】: Recommended Practices for Test Methods for Evaluating the Resistance Spot Welding Behavior of Automotive Sheet Steel Materials
【原文标准名称】: 汽车薄型钢材的耐点焊特性试验方法的推荐性惯例
【标准号】: ANSI/AWS D8.9-2002
ANSI/ASTM D4863-2002 两冲程汽油发动机润滑剂的润滑性测定
【英文标准名称】: Determination of the Lubricity of Two-Stroke Cycle Gasoline Engine Lubricants (05.03)
【原文标准名称】: 两冲程汽油发动机润滑剂的润滑性测定
【标准号】: ANSI/ASTM D4863-2002
【标准状态】: 作废
【国别】:
ANSI/ASTM D4858-2002 润滑剂促使两冲程汽油发动机预点火可能性的测定方法
【英文标准名称】: Determination of the Tendency of Lubricants to Promote Preignition in Two-Stroke-Cycle Gasoline Engines, Test Method for (05.03)
【原文标准名称】: 润滑剂促使两冲程汽油发动机预点火可能性的测定方法
【标准号】: ANSI/ASTM D4858-2002
ANSI/ASTM D6795-2002 加入水和干冰经短时间(30分钟)加热后机油过滤性影响测定方法
【英文标准名称】: Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Water and Dry Ice and a Short (30 Min) Heating Time
【原文标准名称】: 加入水和干冰经短时间(30分钟)加热后机油过滤性影响测定方法
【标准号】: ANSI/ASTM
ANSI/ASTM D6794-2002 加入不同量水经长时间(6小时)加热后发动机油过滤性影响测定方法
【英文标准名称】: Test Method for Measuring the Effect on Filterability of Engine Oils After Treatment with Various Amounts of Water and a Long (6 H) Heating Time
【原文标准名称】: 加入不同量水经长时间(6小时)加热后发动机油过滤性影响测定方法
【标准号】: ANSI/
ANSI/ASTM D4742a-2002 用氧气薄膜吸收法测定汽车发动机油氧化稳定性的方法
【英文标准名称】: Oxidation Stability of Gasoline Automotive Engine Oils by Thin-Film Oxygen Uptake (TFOUT), Test Method for (05.03)
【原文标准名称】: 用氧气薄膜吸收法测定汽车发动机油氧化稳定性的方法
【标准号】: ANSI/ASTM D4742a-2002
【标准
ANSI/ASTM D6823-2002 掺有废润滑油的商用锅炉燃料标准规范
【英文标准名称】: Standard Specification for Commercial Boiler Fuels with Used Lubricating Oils
【原文标准名称】: 掺有废润滑油的商用锅炉燃料标准规范
【标准号】: ANSI/ASTM D6823-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D3527-2002 机动车轮轴承润滑脂的寿命性能的试验方法(05.02)
【英文标准名称】: Test Method for Life Performance of Automotive Wheel Bearing Greases
【原文标准名称】: 机动车轮轴承润滑脂的寿命性能的试验方法(05.02)
【标准号】: ANSI/ASTM D3527-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D6810-2002 利用线性扫描伏安法测定汽轮机油合成树脂酚抗氧化含量的方法
【英文标准名称】: Test Method for Measurement fo Hindered Phenolic Antioxidant Content in Turbine Oil by Linear Sweep Voltammetry
【原文标准名称】: 利用线性扫描伏安法测定汽轮机油合成树脂酚抗氧化含量的方法
【标准号】: ANSI/ASTM D6810-2002
【标准
ANSI/ASTM D6426a-2002 测定中间馏出燃料油可过滤性的方法
【英文标准名称】: Test Method for Determining Filterability of Middle Distillate Fuel Oils
【原文标准名称】: 测定中间馏出燃料油可过滤性的方法
【标准号】: ANSI/ASTM D6426a-2002
【标准状态】: 作废
【国别】: ?拦?br />
ANSI/ASTM D1478-2002 滚珠轴承润滑脂的低温扭矩的试验方法
【英文标准名称】: Test Method for Low-Temperature Torque of Ball Bearing Greases (05.01)
【原文标准名称】: 滚珠轴承润滑脂的低温扭矩的试验方法
【标准号】: ANSI/ASTM D1478-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D3237-2002 原子吸收光谱测定法测定汽油中铅含量的试验方法(05.02)
【英文标准名称】: Lead in Gasoline by Atomic Absorption Spectrometry, Method of Test for (05.02)
【原文标准名称】: 原子吸收光谱测定法测定汽油中铅含量的试验方法(05.02)
【标准号】: ANSI/ASTM D3237-2002
【标准状态】: 作废
【国别
ANSI/ASTM D3231-2002 汽油中磷的测定方法(05.02)
【英文标准名称】: Phosphorus in Gasoline, Method of Test for (05.02)
【原文标准名称】: 汽油中磷的测定方法(05.02)
【标准号】: ANSI/ASTM D3231-2002
【标准状态】: 作废
【国别】: 美国
【发布日期】: 20
ANSI/ASTM D473-2002 原油和燃料油萃取沉淀物试验方法(05.01)
【英文标准名称】: Sediment in Crude and Fuel Oils by Extraction, Method of Test for (05.01)
【原文标准名称】: 原油和燃料油萃取沉淀物试验方法(05.01)
【标准号】: ANSI/ASTM D473-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D94-2002 石油产品皂化值试验(05.01,10.03)
【英文标准名称】: Saponification Number of Petroleum Products, Test for (05.01, 10.03)
【原文标准名称】: 石油产品皂化值试验(05.01,10.03)
【标准号】: ANSI/ASTM D94-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D6791-2002 煅烧石油焦炭晶粒稳定性测定方法
【英文标准名称】: Test Method for the Determination of Grain Stability of Calcined Petroleum Coke
【原文标准名称】: 煅烧石油焦炭晶粒稳定性测定方法
【标准号】: ANSI/ASTM D6791-2002
【标准状态】: 作废
【国别】: 美国
ANSI/ASTM D4951-2002 感应耦合等离子体原子发射光谱法测定润滑油添加元素的方法
【英文标准名称】: Test Method for Determination of Additive Elements in Lubricating Oils by Inductively Coupled Plasma Atomic Emission Spectrometry (05.03)
【原文标准名称】: 感应耦合等离子体原子发射光谱法测定润滑油添加元素的方法
【标准号】: ANSI/ASTM D4951-
ANSI/ASTM D4176-2002 蒸馏燃料游离水和颗粒污染物测试方法(清洁和透明通过/阻止程序)
【英文标准名称】: Test Method for Free Water and Particulate Contamination in Distillate Fuels (Clear and Bright Pass/Fail Proceedings) (05.02)
【原文标准名称】: 蒸馏燃料游离水和颗粒污染物测试方法(清洁和透明通过/阻止程序)
【标准号】: ANSI/ASTM D4176-2002
ANSI/ASTM D2983a-2002 布鲁克非尔德粘度计测量机动车流体润滑剂低温粘度的试验方法
【英文标准名称】: Low-Temperature Viscosity of Automotive Test Fluid Lubricants Measured by Brookfield Viscometer, Method of Test for (05.02)
【原文标准名称】: 布鲁克非尔德粘度计测量机动车流体润滑剂低温粘度的试验方法
【标准号】: ANSI/ASTM D2983a-2002